What is BSP Thread?

BSP Thread

British Standard Pipe (BSP) has been use as standard in plumbing and pipe fittings. There are two types of BSP Thread available. One is Parallel threads or we can say Straight threads and second one is Taper Thread.

BSP is BRITISH STANDARD PIPE THREAD– Also known as Whitworth 55° Thread Form

BSPT is BRITISH STANDARD PIPE TAPER THREAD – Thread form per AS 1722.1, BS 21, ISO 7

BSPP is BRITISH STANDARD PIPE PARALLEL THREAD – Thread form per AS 1722.2, ISO 228

British Standard Pipe Parallel Thread (BSPP)

British Standard Pipe Parallel thread (BSPP) also known as British Standard Pipe Fitting thread (BSPF) and British Standard Pipe Mechanical thread (BSPM). Female and Male thread are both parallel.

BSPP thread used where a pressure-tight joint is achieved by the compression of a soft material (such as an o-ring seal or a washer) between the end face of the male thread and a socket or nipple face, with the tightening of a backnut.

British Standard Pipe Taper Thread (BSPT)

British Standard Pipe Taper thread (BSPT) whose diameter increases or decreases along the length of the thread.

BSPT thread used where pressure-tightness is made through the mating of two threads together. In International standards require all Female thread is parallel and male thread is tapered. Female thread can also be tapered but this is not common.

Thread Count (TPI)

TPI stands for Threads Per Inch, Means the total number of threads per inch measured along the length of a fastener. TPI is used only with American fasteners. Metric Fasteners use a thread Pitch. In general, smaller fasteners have finer threads, so the thread count is higher.

Thread Pitch

Metric fasteners are specified with a thread pitch instead of a thread count. The thread pitch is the distance between threads expressed in millimeters. In general, smaller fasteners have finer thread so they have lower thread pitch.

NPT Threads Dimensions

BSPT & BSPP
SIZE & PITCH
DASH
SIZE
BSPT MALE
THREAD OD
BSPP MALE
THREAD OD
BSPT FEMALE
THREAD ID
BSPP FEMALE
THREAD ID
inch – TPI mm inch mm inch mm inch mm inch
1/8 – 28 -02 9,5 0.37 9,6 0.38 8,4 0.33 8,6 0.34
1/4 – 19 -04 12,8 0.50 13,0 0.51 11,2 0.44 11,9 0.47
3/8 – 19 -06 16,3 0.64 16,5 0.65 14,7 0.59 15,2 0.60
1/2 – 14 -08 20,4 0.80 20,8 0.82 18,3 0.72 19,1 0.75
5/8 – 14 -10 22,5 0.89 22,8 0.90 20,6 0.81 20,8 0.82
3/4 – 14 -12 25,9 1.02 26,3 1.04 23,9 0.94 24,6 0.97
1 – 11 -16 32,6 1.28 33,1 1.30 29,7 1.17 30,7 1.21
1.1/4 – 11 -20 41,1 1.62 41,8 1.64 38,6 1.52 39,4 1.55
1.1/2 – 11 -24 47,0 1.85 47,7 1.88 44,5 1.75 45,5 1.79
2 -11 -32 58,6 2.31 59,5 2.34 56,4 2.22 57,4 2.26
2.1/2 – 11 -40 74,1 2.92 75,1 2.95 71,9 2.83 72,6 2.86
3 – 11 -48 86,6 3.41 87,9 3.46 84,6 3.33 85,4 3.36

Thread size refers to the nominal bore of the pipe.
Subtract approx. 1/4″ (6mm) from thread diameter measurement for nominal pipe size.
Pitch is Threads Per Inch (TPI).
“Gas”, “R” & “G” also refer to BSP.
“Male Iron (Pipe)” may be BSP or NPT.

article from https://www.ryco.com.au/technical/thread-connector-identification/bspt-bspp-threads/

Leave a Reply

Your email address will not be published. Required fields are marked *